The Massey Ferguson 145V tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 4.5 gpm | 17.0 lpm, and hydraulic pressure is 2500 psi | 172.4 bar.
Massey Ferguson 145V Hydraulic Capacity & Flow Specs
| Hydraulic pressure | 2500 psi | 172.4 bar |
|---|---|
| Pump flow | 4.5 gpm | 17.0 lpm |
Massey Ferguson 145V Useful Hydraulic Calculations
| Estimated hydraulic horsepower | about 6.6 hydraulic hp from listed pressure and pump flow |
|---|
Massey Ferguson 145V Hydraulic Comparison Charts
Pump flow comparison
Hydraulic pressure comparison
Benchmarks use practical low, average and high ranges for the compact and small utility tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
Massey Ferguson 145V Steering, Brakes & Mechanical Hydraulic Notes
| Steering | Manual steering |
|---|---|
| Brakes | Wet disc brakes |
Massey Ferguson 145V Hydraulic Capacity FAQ
Why is the Massey Ferguson 145V hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the Massey Ferguson 145V, but pump flow is 4.5 gpm | 17.0 lpm and pressure is 2500 psi | 172.4 bar. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the Massey Ferguson 145V hydraulics feel fast or slow?
The useful speed clue is 4.5 gpm | 17.0 lpm pump flow, below the 8 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the Massey Ferguson 145V hydraulic pressure tell you?
The pressure spec is 2500 psi | 172.4 bar, close to the 2,300 psi benchmark. That is a normal working-pressure number for this tractor category.
What matters most for loader speed on the Massey Ferguson 145V?
On the Massey Ferguson 145V, 4.5 gpm | 17.0 lpm pump flow points to slower loader and cylinder movement and 2,500 psi pressure affects force more than speed. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the Massey Ferguson 145V?
For implement matching, the useful checks are 4.5 gpm flow and 2,500 psi pressure. That combination is more likely to feel slow on loaders, rear remotes and large cylinders and normal on pressure for the class, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Will the Massey Ferguson 145V hydraulics handle long hydraulic jobs?
The useful heat clues are 4.5 gpm flow, 2,500 psi pressure, and about 6.6 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the Massey Ferguson 145V make on paper?
Using 2,500 psi and 4.5 gpm, the rough pressure-flow estimate is about 6.6 hydraulic hp. That is a modest hydraulic power figure, so huge hydraulic loads are not the point of this setup. It is a comparison number, not engine horsepower.
What should you check before servicing the Massey Ferguson 145V hydraulics?
For service planning, pressure is listed at 2,500 psi and flow is listed at 4.5 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official masseyferguson.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
