The New Holland TS130A tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 16.6 gpm | 62.8 lpm, hydraulic pressure is 2755 psi | 190.0 bar, and hydraulic type is open center.
Hydraulic Flow16.6 gpm | 62.8 lpm
Pressure2755 psi | 190.0 bar
Hydraulic Typeopen center
Valves / Remotes2 to 4
New Holland TS130A Hydraulic Capacity & Flow Specs
Hydraulic type
open center
Hydraulic pressure
2755 psi | 190.0 bar
Pump flow
16.6 gpm | 62.8 lpm
Total hydraulic flow
27.1 gpm | 102.6 lpm
Steering flow
10.5 gpm | 39.7 lpm
Rear remotes
2 to 4
New Holland TS130A Hitch, Remote & Lift Specs
Rear hitch type
II
New Holland TS130A Useful Hydraulic Calculations
Total flow vs pump flow
163.3% of listed pump flow
Steering flow vs pump flow
63.3% of listed pump flow
Estimated hydraulic horsepower
about 26.7 hydraulic hp from listed pressure and pump flow
New Holland TS130A Hydraulic Comparison Charts
Pump flow comparison
This model
16.6 gpm
Average
14 gpm
Low
6 gpm
High
28 gpm
Hydraulic pressure comparison
This model
2,755 psi
Average
2,600 psi
Low
2,100 psi
High
3,200 psi
Benchmarks use practical low, average and high ranges for the utility and row-crop tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland TS130A Steering, Brakes & Mechanical Hydraulic Notes
Steering
Power steering
Brakes
Hydraulic wet disc brakes
Differential lock
electro-hydraulic rear
New Holland TS130A Hydraulic Capacity FAQ
Why is the New Holland TS130A hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland TS130A, but pump flow is 16.6 gpm | 62.8 lpm, pressure is 2755 psi | 190.0 bar, and system type is open center. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland TS130A hydraulics feel fast or slow?
The useful speed clue is 16.6 gpm | 62.8 lpm pump flow, above the 14 gpm benchmark for this group. That is the spec that helps loader cycle speed, remote response and hydraulic implement speed.
What does the New Holland TS130A hydraulic pressure tell you?
The pressure spec is 2755 psi | 190.0 bar, close to the 2,600 psi benchmark. That is a normal working-pressure number for this tractor category.
What matters most for loader speed on the New Holland TS130A?
On the New Holland TS130A, 16.6 gpm | 62.8 lpm pump flow points to quicker loader and cylinder movement and 2,755 psi pressure affects force more than speed. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland TS130A?
For implement matching, the useful checks are 16.6 gpm flow, 2,755 psi pressure, 2 to 4 remote/valve listing, and II hitch. That combination is fast enough on paper for quicker cylinder movement than many tractors in this size group and normal on pressure for the class, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Are the New Holland TS130A hydraulic remotes enough?
The New Holland TS130A remote/valve listing is 2 to 4. Because that wording may be optional or configuration-dependent, treat it as a setup check before buying an implement that needs rear hydraulic outlets.
Will the New Holland TS130A hydraulics handle long hydraulic jobs?
The useful heat clues are 16.6 gpm flow, 2,755 psi pressure, and about 26.7 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the New Holland TS130A make on paper?
Using 2,755 psi and 16.6 gpm, the rough pressure-flow estimate is about 26.7 hydraulic hp. That is a useful middle-range hydraulic power figure for normal tractor work. It is a comparison number, not engine horsepower.
What do the New Holland TS130A hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the New Holland TS130A use?
The hydraulic system is listed as open center with 16.6 gpm | 62.8 lpm pump flow and 2755 psi | 190.0 bar pressure. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
