The New Holland TS120 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 9.3 gpm | 35.2 lpm, hydraulic pressure is 2611 psi | 180.0 bar, and hydraulic type is open center.
Hydraulic Flow9.3 gpm | 35.2 lpm
Pressure2611 psi | 180.0 bar
Hydraulic Typeopen center
Lift Capacity11003 lbs | 4990 kg
New Holland TS120 Hydraulic Capacity & Flow Specs
Hydraulic type
open center
Hydraulic pressure
2611 psi | 180.0 bar
Pump flow
9.3 gpm | 35.2 lpm
New Holland TS120 Hitch, Remote & Lift Specs
Rear hitch type
II
Rear hitch control
position and draft control
Rear lift at 24 inches
11003 lbs | 4990 kg
New Holland TS120 Useful Hydraulic Calculations
Rear lift per pump gpm
1,183.1 lb per gpm
Estimated hydraulic horsepower
about 14.2 hydraulic hp from listed pressure and pump flow
New Holland TS120 Hydraulic Comparison Charts
Pump flow comparison
This model
9.3 gpm
Average
14 gpm
Low
6 gpm
High
28 gpm
Hydraulic pressure comparison
This model
2,611 psi
Average
2,600 psi
Low
2,100 psi
High
3,200 psi
Rear lift comparison
This model
11,003 lb
Average
7,000 lb
Low
3,000 lb
High
12,000 lb
Benchmarks use practical low, average and high ranges for the utility and row-crop tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland TS120 Steering, Brakes & Mechanical Hydraulic Notes
Steering
Power steering
Brakes
Wet disc brakes
New Holland TS120 Hydraulic Capacity FAQ
Why is the New Holland TS120 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland TS120, but pump flow is 9.3 gpm | 35.2 lpm, pressure is 2611 psi | 180.0 bar, system type is open center, and lift is listed as 11003 lbs | 4990 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland TS120 hydraulics feel fast or slow?
The useful speed clue is 9.3 gpm | 35.2 lpm pump flow, below the 14 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the New Holland TS120 hydraulic pressure tell you?
The pressure spec is 2611 psi | 180.0 bar, close to the 2,600 psi benchmark. That is a normal working-pressure number for this tractor category.
What matters most for loader speed on the New Holland TS120?
On the New Holland TS120, 9.3 gpm | 35.2 lpm pump flow points to slower loader and cylinder movement, 2,611 psi pressure affects force more than speed, and 11,003 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland TS120?
For implement matching, the useful checks are 9.3 gpm flow, 2,611 psi pressure, 11,003 lb listed lift, and II hitch. That combination is more likely to feel slow on loaders, rear remotes and large cylinders, normal on pressure for the class, and better suited to heavier mounted implements, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the New Holland TS120 rear lift capacity strong?
The listed lift figure is 11003 lbs | 4990 kg, above the 7,000 lb benchmark. That points to a stronger hitch setup, but ballast, tire grip and implement length can still be the real limit.
Will the New Holland TS120 hydraulics handle long hydraulic jobs?
The useful heat clues are 9.3 gpm flow, 2,611 psi pressure, and about 14.2 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the New Holland TS120 make on paper?
Using 2,611 psi and 9.3 gpm, the rough pressure-flow estimate is about 14.2 hydraulic hp. That is a modest hydraulic power figure, so huge hydraulic loads are not the point of this setup. It is a comparison number, not engine horsepower.
What do the New Holland TS120 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II, hitch control is position and draft control, and listed lift is 11003 lbs | 4990 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the New Holland TS120 use?
The hydraulic system is listed as open center with 9.3 gpm | 35.2 lpm pump flow and 2611 psi | 180.0 bar pressure. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
