The New Holland TS100A tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 16.6 gpm (open center) | 62.8 lpm, hydraulic pressure is 2755 psi | 190.0 bar, and hydraulic type is open center.
Hydraulic Flow16.6 gpm (open center) | 62.8 lpm
Pressure2755 psi | 190.0 bar
Hydraulic Typeopen center
Valves / Remotes2 to 4
Lift Capacity13708.3 lbs | 6218 kg
New Holland TS100A Hydraulic Capacity & Flow Specs
Hydraulic type
open center
Hydraulic pressure
2755 psi | 190.0 bar
Pump flow
16.6 gpm (open center) | 62.8 lpm
Steering flow
10.5 gpm | 39.7 lpm
Rear remotes
2 to 4
New Holland TS100A Hitch, Remote & Lift Specs
Rear hitch type
II
Rear lift at ends
13708.3 lbs | 6218 kg
New Holland TS100A Useful Hydraulic Calculations
Steering flow vs pump flow
63.3% of listed pump flow
Rear lift per pump gpm
825.8 lb per gpm
Estimated hydraulic horsepower
about 26.7 hydraulic hp from listed pressure and pump flow
New Holland TS100A Hydraulic Comparison Charts
Pump flow comparison
This model
16.6 gpm
Average
50 gpm
Low
25 gpm
High
90 gpm
Hydraulic pressure comparison
This model
2,755 psi
Average
3,100 psi
Low
2,600 psi
High
3,700 psi
Rear lift comparison
This model
13,708.3 lb
Average
15,500 lb
Low
9,000 lb
High
26,000 lb
Benchmarks use practical low, average and high ranges for the large ag tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland TS100A Steering, Brakes & Mechanical Hydraulic Notes
Steering
Power steering
Brakes
Hydraulic wet disc brakes
Differential lock
electro-hydraulic rear
New Holland TS100A Hydraulic Capacity FAQ
Why is the New Holland TS100A hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland TS100A, but pump flow is 16.6 gpm (open center) | 62.8 lpm, pressure is 2755 psi | 190.0 bar, system type is open center, and lift is listed as 13708.3 lbs | 6218 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland TS100A hydraulics feel fast or slow?
The useful speed clue is 16.6 gpm (open center) | 62.8 lpm pump flow, below the 50 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the New Holland TS100A hydraulic pressure tell you?
The pressure spec is 2755 psi | 190.0 bar, below the 3,100 psi benchmark. Pressure is the force side of hydraulics, so this matters more for lift and cylinder push than for speed.
What matters most for loader speed on the New Holland TS100A?
On the New Holland TS100A, 16.6 gpm (open center) | 62.8 lpm pump flow points to slower loader and cylinder movement, 2,755 psi pressure affects force more than speed, and 13,708.3 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland TS100A?
For implement matching, the useful checks are 16.6 gpm flow, 2,755 psi pressure, 13,708.3 lb listed lift, and 2 to 4 remote/valve listing. That combination is more likely to feel slow on loaders, rear remotes and large cylinders and not a brute-force hydraulic setup compared with higher-pressure systems, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the New Holland TS100A rear lift capacity strong?
The listed lift figure is 13708.3 lbs | 6218 kg, close to the 15,500 lb benchmark. It is in the normal range, so implement length and ballast matter as much as the headline lift number.
Are the New Holland TS100A hydraulic remotes enough?
The New Holland TS100A remote/valve listing is 2 to 4. Because that wording may be optional or configuration-dependent, treat it as a setup check before buying an implement that needs rear hydraulic outlets.
Will the New Holland TS100A hydraulics handle long hydraulic jobs?
The useful heat clues are 16.6 gpm flow, 2,755 psi pressure, and about 26.7 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the New Holland TS100A make on paper?
Using 2,755 psi and 16.6 gpm, the rough pressure-flow estimate is about 26.7 hydraulic hp. That is a useful middle-range hydraulic power figure for normal tractor work. It is a comparison number, not engine horsepower.
What do the New Holland TS100A hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II and listed lift is 13708.3 lbs | 6218 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
