The Massey Ferguson 294C tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 9.4 gpm (hitch pump) | 35.6 lpm, hydraulic pressure is 2148 psi | 148.1 bar, and hydraulic type is open center.
Massey Ferguson 294C Hydraulic Capacity & Flow Specs
| Hydraulic type | open center |
|---|---|
| Hydraulic pressure | 2148 psi | 148.1 bar |
| Pump flow | 9.4 gpm (hitch pump) | 35.6 lpm |
Massey Ferguson 294C Hitch, Remote & Lift Specs
| Rear hitch type | II |
|---|---|
| Rear hitch control | position, response, and draft control |
| Rear lift at ends | 5289 lbs | 2399 kg |
Massey Ferguson 294C Useful Hydraulic Calculations
| Rear lift per pump gpm | 562.7 lb per gpm |
|---|---|
| Estimated hydraulic horsepower | about 11.8 hydraulic hp from listed pressure and pump flow |
Massey Ferguson 294C Hydraulic Comparison Charts
Pump flow comparison
Hydraulic pressure comparison
Rear lift comparison
Benchmarks use practical low, average and high ranges for the utility and row-crop tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
Massey Ferguson 294C Hydraulic Capacity FAQ
Why is the Massey Ferguson 294C hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the Massey Ferguson 294C, but pump flow is 9.4 gpm (hitch pump) | 35.6 lpm, pressure is 2148 psi | 148.1 bar, system type is open center, and lift is listed as 5289 lbs | 2399 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the Massey Ferguson 294C hydraulics feel fast or slow?
The useful speed clue is 9.4 gpm (hitch pump) | 35.6 lpm pump flow, below the 14 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the Massey Ferguson 294C hydraulic pressure tell you?
The pressure spec is 2148 psi | 148.1 bar, below the 2,600 psi benchmark. Pressure is the force side of hydraulics, so this matters more for lift and cylinder push than for speed.
What matters most for loader speed on the Massey Ferguson 294C?
On the Massey Ferguson 294C, 9.4 gpm (hitch pump) | 35.6 lpm pump flow points to slower loader and cylinder movement, 2,148 psi pressure affects force more than speed, and 5,289 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the Massey Ferguson 294C?
For implement matching, the useful checks are 9.4 gpm flow, 2,148 psi pressure, 5,289 lb listed lift, and II hitch. That combination is more likely to feel slow on loaders, rear remotes and large cylinders, not a brute-force hydraulic setup compared with higher-pressure systems, and best kept realistic on heavy rear implements, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the Massey Ferguson 294C rear lift capacity strong?
The listed lift figure is 5289 lbs | 2399 kg, below the 7,000 lb benchmark. Keep rear implements realistic and pay attention to weight carried behind the lift points.
Will the Massey Ferguson 294C hydraulics handle long hydraulic jobs?
The useful heat clues are 9.4 gpm flow, 2,148 psi pressure, and about 11.8 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the Massey Ferguson 294C make on paper?
Using 2,148 psi and 9.4 gpm, the rough pressure-flow estimate is about 11.8 hydraulic hp. That is a modest hydraulic power figure, so huge hydraulic loads are not the point of this setup. It is a comparison number, not engine horsepower.
What do the Massey Ferguson 294C hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II, hitch control is position, response, and draft control, and listed lift is 5289 lbs | 2399 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the Massey Ferguson 294C use?
The hydraulic system is listed as open center with 9.4 gpm (hitch pump) | 35.6 lpm pump flow and 2148 psi | 148.1 bar pressure. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official masseyferguson.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
