For the John Deere 6110SE, coolant capacity is 8.06 gal (30.5 L). Coolant choice is listed as John Deere Cool-Gard II, with 40/60 coolant and water mix guidance.
Coolant capacity8.06 gal (30.5 L)Cooling system refill amount
Antifreeze mix40/60 coolant and water mixFreeze/boil protection
John Deere 6110SE Coolant Capacity Specs
Coolant capacity
8.06 gal (30.5 L)
Coolant type
John Deere Cool-Gard II
Antifreeze mix
40/60 coolant and water mix
Engine horsepower
80 hp
Engine displacement
4.5 L (274.6 cu in)
John Deere 6110SE Coolant Capacity Guide
Coolant capacity guide
This model
8.06 gal
Class low
6 gal
Class typical
9.5 gal
Class high
14 gal
Compared with a broad 6 series guide, not the full tractor dataset.
John Deere 6110SE Coolant Service Notes
Coolant capacity note
The useful service number here is 8.06 gal (30.5 L). Keep some extra coolant available because trapped air can lower the level after the first warm-up
Coolant service note
For a full coolant service on the John Deere 6110SE, plan around 8.06 gal (30.5 L) and match the listed coolant guidance: John Deere Cool-Gard II and 40/60 coolant and water mix
Coolant type note
The John Deere 6110SE coolant type is John Deere Cool-Gard II. Wrong coolant chemistry can reduce corrosion, freeze and boil protection
Antifreeze mix note
The listed mix for the John Deere 6110SE is 40/60 coolant and water mix. Keep the coolant strength in range after a drain, flush or top-up
Refill check
After a drain and refill on the John Deere 6110SE, the cooling system can burp air. Recheck the level after the first warm-up and cool-down cycle
Engine context
The John Deere 6110SE engine specs listed with this page are engine horsepower 80 hp and engine displacement 4.5 L (274.6 cu in). They help identify the machine, but they are not a substitute for the coolant capacity
John Deere 6110SE Coolant Capacity FAQ
How much coolant should I buy for the John Deere 6110SE?
The cooling system capacity for the John Deere 6110SE is 8.06 gal (30.5 L). This is the main refill figure for a drain, flush or coolant change
Is John Deere Cool-Gard II listed for the John Deere 6110SE?
For the John Deere 6110SE, the coolant type is listed as John Deere Cool-Gard II. Avoid mixing incompatible coolant products
What mix ratio should I use when refilling the John Deere 6110SE?
If using concentrate for the John Deere 6110SE, mix it to 40/60 coolant and water mix before filling unless the product label says it is already premixed
Do I fill the John Deere 6110SE exactly to capacity or check the level marks?
Fill the John Deere 6110SE slowly, run it with the heater/thermostat cycle where applicable, let it cool and check the level again. That helps catch trapped air
Can I just add coolant to the John Deere 6110SE if the level is low?
Flush the John Deere 6110SE cooling system if the coolant is dirty, contaminated, badly diluted or overdue for service. A simple top-up does not fix old coolant chemistry
Official information note
Mistakes do happen. Tractor coolant capacity and coolant type can change by year, market, engine, radiator setup and service procedure. Check the operator manual, service manual and official deere.com website before draining, flushing or refilling the cooling system.
