Coolant capacity for the John Deere S130 is 9.51 gal (36 L). The coolant type is listed as John Deere Cool-Gard II, and the antifreeze mix is 50/50 coolant and water mix.
Coolant capacity9.51 gal (36 L)Cooling system refill amount
Antifreeze mix50/50 coolant and water mixFreeze/boil protection
John Deere S130 Coolant Capacity Specs
Coolant capacity
9.51 gal (36 L)
Coolant type
John Deere Cool-Gard II
Antifreeze mix
50/50 coolant and water mix
Engine model
John Deere S130 tractor features a Briggs
Engine horsepower
22 hp
Engine displacement
44.2 cu in (0.72 L)
John Deere S130 Coolant Capacity Guide
Coolant capacity guide
This model
9.51 gal
Class low
0.8 gal
Class typical
2.5 gal
Class high
5 gal
Compared with a broad older small tractor guide, not the full tractor dataset.
John Deere S130 Coolant Service Notes
Coolant capacity note
The John Deere S130 cooling system is listed at 9.51 gal (36 L). Final level can settle after the first heat cycle, so recheck the level after service
Coolant service note
A proper coolant change on the John Deere S130 means using the 9.51 gal (36 L) capacity and keeping the coolant chemistry consistent with John Deere Cool-Gard II and 50/50 coolant and water mix
Coolant type note
For the John Deere S130, coolant choice is listed as John Deere Cool-Gard II. Capacity tells you how much; coolant type tells you what to use
Antifreeze mix note
The John Deere S130 coolant mix guidance is 50/50 coolant and water mix. This matters most in freezing weather, hot work and long service intervals
Refill check
For the John Deere S130, 9.51 gal (36 L) is the planned refill amount. The final level may need a small top-up after trapped air leaves the system
Engine context
For comparison, the John Deere S130 engine details listed here are engine model John Deere S130 tractor features a Briggs, engine horsepower 22 hp, and engine displacement 44.2 cu in (0.72 L). The coolant capacity remains the service number to use for refilling
John Deere S130 Coolant Capacity FAQ
What is the refill amount for the John Deere S130 cooling system?
For coolant service, the John Deere S130 is listed at 9.51 gal (36 L). Buy enough coolant for that amount and confirm the final level at the machine
What should I match when topping up coolant in the John Deere S130?
The listed coolant type for the John Deere S130 is John Deere Cool-Gard II. Match that coolant chemistry before topping up or flushing the system
Should I use premixed coolant in the John Deere S130?
The John Deere S130 uses 50/50 coolant and water mix where that mix is specified. Confirm the mix against your climate and manual
Should I run the John Deere S130 after adding coolant?
Do not judge the job only by pouring in 9.51 gal (36 L). The final check is the actual radiator or overflow level after the system has burped air
When is a full coolant flush better than a top-up on the John Deere S130?
Topping up is fine for a small low-level correction. If the coolant is old, rusty, oily, diluted or the wrong type, drain and flush the system using the 9.51 gal (36 L) capacity as the refill guide
Official information note
Mistakes do happen. Tractor coolant capacity and coolant type can change by year, market, engine, radiator setup and service procedure. Check the operator manual, service manual and official deere.com website before draining, flushing or refilling the cooling system.
