The New Holland Workmaster 65 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 10.4 gpm | 39.4 lpm, hydraulic type is open center fixed displacement, and valves/remotes are listed as 1 or 2.
Hydraulic Flow10.4 gpm | 39.4 lpm
Hydraulic Typeopen center fixed displacement
Valves / Remotes1 or 2
Lift Capacity3,276 lbs | 1485 kg
New Holland Workmaster 65 Hydraulic Capacity & Flow Specs
Hydraulic type
open center fixed displacement
Pump flow
10.4 gpm | 39.4 lpm
Total hydraulic flow
18.7 gpm | 70.8 lpm
Steering flow
5.3 gpm | 20.1 lpm
Rear remotes
1 or 2
New Holland Workmaster 65 Hitch, Remote & Lift Specs
Rear hitch type
2/1
Rear hitch control
position control and mechanical draft sensing
Rear lift at ends
3,276 lbs | 1485 kg
New Holland Workmaster 65 Useful Hydraulic Calculations
Total flow vs pump flow
179.8% of listed pump flow
Steering flow vs pump flow
51% of listed pump flow
Rear lift per pump gpm
315 lb per gpm
New Holland Workmaster 65 Hydraulic Comparison Charts
Pump flow comparison
This model
10.4 gpm
Average
8 gpm
Low
3.5 gpm
High
14 gpm
Rear lift comparison
This model
3,276 lb
Average
1,800 lb
Low
800 lb
High
3,200 lb
Benchmarks use practical low, average and high ranges for the compact and small utility tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland Workmaster 65 Steering, Brakes & Mechanical Hydraulic Notes
Steering
hydrostatic power
Brakes
mechanical wet disc brakes
Differential lock
mechanical rear lock engaged by foot pedal, limited slip front differential (4WD)
New Holland Workmaster 65 Hydraulic Capacity FAQ
Why is the New Holland Workmaster 65 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland Workmaster 65, but pump flow is 10.4 gpm | 39.4 lpm, system type is open center fixed displacement, and lift is listed as 3,276 lbs | 1485 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland Workmaster 65 hydraulics feel fast or slow?
The useful speed clue is 10.4 gpm | 39.4 lpm pump flow, above the 8 gpm benchmark for this group. That is the spec that helps loader cycle speed, remote response and hydraulic implement speed.
What matters most for loader speed on the New Holland Workmaster 65?
On the New Holland Workmaster 65, 10.4 gpm | 39.4 lpm pump flow points to quicker loader and cylinder movement and 3,276 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland Workmaster 65?
For implement matching, the useful checks are 10.4 gpm flow, 3,276 lb listed lift, 1 or 2 remote/valve listing, and 2/1 hitch. That combination is fast enough on paper for quicker cylinder movement than many tractors in this size group and better suited to heavier mounted implements, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the New Holland Workmaster 65 rear lift capacity strong?
The listed lift figure is 3,276 lbs | 1485 kg, above the 1,800 lb benchmark. That points to a stronger hitch setup, but ballast, tire grip and implement length can still be the real limit.
Are the New Holland Workmaster 65 hydraulic remotes enough?
The New Holland Workmaster 65 remote/valve listing is 1 or 2. Because that wording may be optional or configuration-dependent, treat it as a setup check before buying an implement that needs rear hydraulic outlets.
Will the New Holland Workmaster 65 hydraulics handle long hydraulic jobs?
The useful heat clues are 10.4 gpm flow. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
What do the New Holland Workmaster 65 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is 2/1, hitch control is position control and mechanical draft sensing, and listed lift is 3,276 lbs | 1485 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the New Holland Workmaster 65 use?
The hydraulic system is listed as open center fixed displacement with 10.4 gpm | 39.4 lpm pump flow. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
What should you check before servicing the New Holland Workmaster 65 hydraulics?
For service planning, the system is listed as open center fixed displacement and flow is listed at 10.4 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
