The New Holland TK4060 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 11.9 gpm | 45.0 lpm, hydraulic pressure is 2,755 psi | 190.0 bar, and hydraulic type is open center.
Hydraulic Flow11.9 gpm | 45.0 lpm
Pressure2,755 psi | 190.0 bar
Hydraulic Typeopen center
Valves / Remotes3 to 4
New Holland TK4060 Hydraulic Capacity & Flow Specs
Hydraulic type
open center
Hydraulic pressure
2,755 psi | 190.0 bar
Pump flow
11.9 gpm | 45.0 lpm
Total hydraulic flow
17.7 gpm | 67.0 lpm
Steering flow
5.8 gpm | 22.0 lpm
Hydraulic valves
3 to 4
New Holland TK4060 Useful Hydraulic Calculations
Total flow vs pump flow
148.7% of listed pump flow
Steering flow vs pump flow
48.7% of listed pump flow
Estimated hydraulic horsepower
about 19.1 hydraulic hp from listed pressure and pump flow
New Holland TK4060 Hydraulic Comparison Charts
Pump flow comparison
This model
11.9 gpm
Average
8 gpm
Low
3.5 gpm
High
14 gpm
Hydraulic pressure comparison
This model
2,755 psi
Average
2,300 psi
Low
1,800 psi
High
3,000 psi
Benchmarks use practical low, average and high ranges for the compact and small utility tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland TK4060 Hydraulic Capacity FAQ
Why is the New Holland TK4060 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland TK4060, but pump flow is 11.9 gpm | 45.0 lpm, pressure is 2,755 psi | 190.0 bar, and system type is open center. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland TK4060 hydraulics feel fast or slow?
The useful speed clue is 11.9 gpm | 45.0 lpm pump flow, above the 8 gpm benchmark for this group. That is the spec that helps loader cycle speed, remote response and hydraulic implement speed.
What does the New Holland TK4060 hydraulic pressure tell you?
The pressure spec is 2,755 psi | 190.0 bar, above the 2,300 psi benchmark. That gives the system stronger force potential, but the implement, hoses, couplers and relief settings still have to match.
What matters most for loader speed on the New Holland TK4060?
On the New Holland TK4060, 11.9 gpm | 45.0 lpm pump flow points to quicker loader and cylinder movement and 2,755 psi pressure affects force more than speed. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland TK4060?
For implement matching, the useful checks are 11.9 gpm flow, 2,755 psi pressure, and 3 to 4 remote/valve listing. That combination is fast enough on paper for quicker cylinder movement than many tractors in this size group and strong on hydraulic force if the cylinders and relief settings match, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Are the New Holland TK4060 hydraulic remotes enough?
The New Holland TK4060 remote/valve listing is 3 to 4. Because that wording may be optional or configuration-dependent, treat it as a setup check before buying an implement that needs rear hydraulic outlets.
Will the New Holland TK4060 hydraulics handle long hydraulic jobs?
The useful heat clues are 11.9 gpm flow, 2,755 psi pressure, and about 19.1 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the New Holland TK4060 make on paper?
Using 2,755 psi and 11.9 gpm, the rough pressure-flow estimate is about 19.1 hydraulic hp. That is a useful middle-range hydraulic power figure for normal tractor work. It is a comparison number, not engine horsepower.
What hydraulic system does the New Holland TK4060 use?
The hydraulic system is listed as open center with 11.9 gpm | 45.0 lpm pump flow and 2,755 psi | 190.0 bar pressure. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
What should you check before servicing the New Holland TK4060 hydraulics?
For service planning, the system is listed as open center, pressure is listed at 2,755 psi, and flow is listed at 11.9 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
