The Case IH 1130 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 7.2 gpm | 27.3 lpm, hydraulic pressure is 2133 psi | 147.1 bar, and hydraulic type is open center.
Hydraulic Flow7.2 gpm | 27.3 lpm
Pressure2133 psi | 147.1 bar
Hydraulic Typeopen center
Valves / Remotes1
Lift Capacity1653 lbs | 749 kg
Case IH 1130 Hydraulic Capacity & Flow Specs
Hydraulic type
open center
Hydraulic pressure
2133 psi | 147.1 bar
Pump flow
7.2 gpm | 27.3 lpm
Steering flow
3.2 gpm | 12.1 lpm
Hydraulic valves
1
Case IH 1130 Hitch, Remote & Lift Specs
Rear hitch type
I
Rear lift at ends
2205 lbs | 1000 kg
Rear lift at 24 inches
1653 lbs | 749 kg
Case IH 1130 Useful Hydraulic Calculations
Steering flow vs pump flow
44.4% of listed pump flow
Rear lift per pump gpm
229.6 lb per gpm
Estimated hydraulic horsepower
about 9 hydraulic hp from listed pressure and pump flow
Pump flow per listed valve
7.2 gpm per valve
Case IH 1130 Hydraulic Comparison Charts
Pump flow comparison
This model
7.2 gpm
Average
8 gpm
Low
3.5 gpm
High
14 gpm
Hydraulic pressure comparison
This model
2,133 psi
Average
2,300 psi
Low
1,800 psi
High
3,000 psi
Rear lift comparison
This model
1,653 lb
Average
1,800 lb
Low
800 lb
High
3,200 lb
Valve / remote count comparison
This model
1
Average
1
Low
0
High
3
Benchmarks use practical low, average and high ranges for the compact and small utility tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
Case IH 1130 Steering, Brakes & Mechanical Hydraulic Notes
Steering
Power steering
Brakes
Wet disc brakes
Case IH 1130 Hydraulic Capacity FAQ
Why is the Case IH 1130 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the Case IH 1130, but pump flow is 7.2 gpm | 27.3 lpm, pressure is 2133 psi | 147.1 bar, system type is open center, and lift is listed as 1653 lbs | 749 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the Case IH 1130 hydraulics feel fast or slow?
The useful speed clue is 7.2 gpm | 27.3 lpm pump flow, close to the 8 gpm benchmark for this group. It should be normal for general tractor hydraulic work, assuming the pump and valves are healthy.
What does the Case IH 1130 hydraulic pressure tell you?
The pressure spec is 2133 psi | 147.1 bar, close to the 2,300 psi benchmark. That is a normal working-pressure number for this tractor category.
What matters most for loader speed on the Case IH 1130?
On the Case IH 1130, 7.2 gpm | 27.3 lpm pump flow is around normal for loader/cylinder speed, 2,133 psi pressure affects force more than speed, and 1,653 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the Case IH 1130?
For implement matching, the useful checks are 7.2 gpm flow, 2,133 psi pressure, 1,653 lb listed lift, and 1 remote/valve listing. That combination is in the normal flow range for this size group and normal on pressure for the class, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the Case IH 1130 rear lift capacity strong?
The listed lift figure is 1653 lbs | 749 kg, close to the 1,800 lb benchmark. It is in the normal range, so implement length and ballast matter as much as the headline lift number.
Are the Case IH 1130 hydraulic remotes enough?
The Case IH 1130 lists 1 for valves/remotes. That is about normal for this category.
Will the Case IH 1130 hydraulics handle long hydraulic jobs?
The useful heat clues are 7.2 gpm flow, 2,133 psi pressure, and about 9 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the Case IH 1130 make on paper?
Using 2,133 psi and 7.2 gpm, the rough pressure-flow estimate is about 9 hydraulic hp. That is a modest hydraulic power figure, so huge hydraulic loads are not the point of this setup. It is a comparison number, not engine horsepower.
What do the Case IH 1130 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is I and listed lift is 1653 lbs | 749 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official caseih.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
