The Massey Ferguson 4710M tractor cooling system capacity is 3.3 gal | 12.5 L, coolant type is 50/50 ethylene glycol-based coolant, and coolant change interval is every 500 hours.
Massey Ferguson 4710M Coolant Capacity Details
Cooling system capacity
3.3 gal | 12.5 L
Coolant type
50/50 ethylene glycol-based coolant
Coolant change interval
Every 500 hours
Radiator cap pressure
15 psi | 103 kPa
Coolant Capacity Comparison Chart
Coolant Capacity Comparison
This model
3.3 gal
Average
5.5 gal
Low
3 gal
High
9 gal
Benchmarks use practical low, average and high coolant-capacity ranges for the utility tractor category. Use the exact tractor manual before buying coolant.
Massey Ferguson 4710M Extra Coolant Notes
Engine horsepower
60 hp | 44.7 kW
Engine displacement
3.3 L | 201 cu in
Capacity note
For the Massey Ferguson 4710M, the listed cooling system capacity is 3.3 gal | 12.5 L. Buy slightly more coolant than the exact capacity so you have enough for topping off after air burps out.
Mixture note
Use the coolant type listed above and match the antifreeze/water mix to the operator manual and local freezing conditions.
Radiator cap note
The radiator cap pressure listed for the Massey Ferguson 4710M is 15 psi | 103 kPa. Do not replace it with a random cap unless the pressure rating matches.
Refill note
Refill slowly, run the tractor until warm with the heater circuit open if fitted, let it cool, then recheck the coolant level. Never remove a hot radiator cap under pressure.
Massey Ferguson 4710M Coolant FAQs
How much coolant does a Massey Ferguson 4710M take?
The Massey Ferguson 4710M takes 3.3 gal | 12.5 L of coolant. That is on the low side for the utility tractor benchmark, which makes the refill cheaper, but the level still needs to be checked after the first heat cycle.
Is 3.3 gal | 12.5 L a small coolant capacity for a Massey Ferguson 4710M?
It is low compared with the benchmark on this page. That makes the job cheaper, but it does not make coolant choice or bleeding less important.
How many coolant jugs do I need for a Massey Ferguson 4710M?
This is a manageable refill amount. A 3.3 gal | 12.5 L system needs about 4 one-gallon containers if you are using premixed coolant. If using concentrate at a 50/50 mix, plan on about 1.6 gal of concentrate and 1.6 gal of distilled water. In metric terms, that is roughly 3 x 5 L containers for a full premix refill.
What coolant should I use in a Massey Ferguson 4710M?
The listed coolant is 50/50 ethylene glycol-based coolant. Ethylene glycol tells you the base coolant, but the additive package still matters on diesel engines, so match the manual or an approved equivalent.
Can I use a different radiator cap on a Massey Ferguson 4710M?
The listed cap pressure is 15 psi | 103 kPa. That higher-pressure cap helps raise the boiling point, but only if the radiator neck, hoses and overflow path are in good shape. A weak cap or damaged seat can still cause coolant loss.
When should the Massey Ferguson 4710M coolant be changed?
The listed interval is every 500 hours. Hour-based service matters most on working tractors that spend long periods hot under load.
Official information note
Mistakes do happen. Coolant specs can change by year, engine, market, radiator option and coolant chemistry. Check the operator manual, parts book and official masseyferguson.com website before draining, flushing or refilling the cooling system.
