The New Holland TM190 tractor hydraulic capacity is 26.4 gal | 99.9 L, pump flow is 31.7 gpm | 120.0 lpm, and hydraulic pressure is 2750 psi | 189.6 bar.
Hydraulic Capacity26.4 gal | 99.9 L
Hydraulic Flow31.7 gpm | 120.0 lpm
Pressure2750 psi | 189.6 bar
Hydraulic Typeclosed center load sensing (CCLS)
Valves / Remotes4
Lift Capacity17500 lbs | 7938 kg
New Holland TM190 Hydraulic Capacity & Flow Specs
Hydraulic type
closed center load sensing (CCLS)
Hydraulic capacity
26.4 gal | 99.9 L
Hydraulic pressure
2750 psi | 189.6 bar
Pump flow
31.7 gpm | 120.0 lpm
Total hydraulic flow
48.7 gpm | 184.3 lpm
Steering flow
17 gpm | 64.3 lpm
Rear remotes
4
New Holland TM190 Hitch, Remote & Lift Specs
Rear hitch type
II/IIIN
Rear hitch control
electronic lower-link draft control
Rear lift at ends
17500 lbs | 7938 kg
Front lift
7208 lbs | 3269 kg
New Holland TM190 Useful Hydraulic Calculations
Pump flow per gallon of hydraulic capacity
1.2 gpm per gal
Hydraulic tank turnover estimate
about 0.8 minutes at rated pump flow
Total flow vs pump flow
153.6% of listed pump flow
Steering flow vs pump flow
53.6% of listed pump flow
Rear lift per pump gpm
552.1 lb per gpm
Rear lift per hydraulic gallon
662.9 lb per gal
Estimated hydraulic horsepower
about 50.9 hydraulic hp from listed pressure and pump flow
Pump flow per listed valve
7.9 gpm per valve
Metric capacity vs pump flow
99.9 L capacity with 31.7 gpm pump flow
New Holland TM190 Hydraulic Comparison Charts
Hydraulic capacity comparison
This model
26.4 gal
Average
42 gal
Low
22 gal
High
80 gal
Pump flow comparison
This model
31.7 gpm
Average
50 gpm
Low
25 gpm
High
90 gpm
Hydraulic pressure comparison
This model
2,750 psi
Average
3,100 psi
Low
2,600 psi
High
3,700 psi
Rear lift comparison
This model
17,500 lb
Average
15,500 lb
Low
9,000 lb
High
26,000 lb
Valve / remote count comparison
This model
4
Average
5
Low
3
High
8
Benchmarks use practical low, average and high ranges for the large ag tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland TM190 Steering, Brakes & Mechanical Hydraulic Notes
Steering
Power steering
Brakes
hydraulic wet disc brakes
Differential lock
electro-hydraulic
New Holland TM190 Hydraulic Capacity FAQ
Is the New Holland TM190 hydraulic capacity big or small for its size?
The New Holland TM190 lists 26.4 gal | 99.9 L of hydraulic capacity, which is below the 42 gal benchmark for this group. Real talk: that is not automatically bad, but it gives you less oil volume as a heat buffer during loader work, hydraulic motors or long remote use.
Will the New Holland TM190 hydraulics feel fast or slow?
The useful speed clue is 31.7 gpm | 120.0 lpm pump flow, below the 50 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the New Holland TM190 hydraulic pressure tell you?
The pressure spec is 2750 psi | 189.6 bar, below the 3,100 psi benchmark. Pressure is the force side of hydraulics, so this matters more for lift and cylinder push than for speed.
What matters most for loader speed on the New Holland TM190?
On the New Holland TM190, 31.7 gpm | 120.0 lpm pump flow points to slower loader and cylinder movement, 2,750 psi pressure affects force more than speed, and 17,500 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland TM190?
For implement matching, the useful checks are 31.7 gpm flow, 2,750 psi pressure, 17,500 lb listed lift, and 4 remote/valve listing. That combination is more likely to feel slow on loaders, rear remotes and large cylinders, not a brute-force hydraulic setup compared with higher-pressure systems, and better suited to heavier mounted implements, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the New Holland TM190 rear lift capacity strong?
The listed lift figure is 17500 lbs | 7938 kg, above the 15,500 lb benchmark. That points to a stronger hitch setup, but ballast, tire grip and implement length can still be the real limit.
Are the New Holland TM190 hydraulic remotes enough?
The New Holland TM190 lists 4 for valves/remotes. That is slightly under the 5 benchmark, but still a workable/normal remote count for many setups.
Will the New Holland TM190 hydraulics handle long hydraulic jobs?
The useful heat clues are 26.4 gal of hydraulic capacity, 31.7 gpm flow, 2,750 psi pressure, and about 50.9 hydraulic hp by the pressure-flow estimate. That is a fairly normal flow-to-oil-volume relationship for mixed tractor work.
How much hydraulic power does the New Holland TM190 make on paper?
Using 2,750 psi and 31.7 gpm, the rough pressure-flow estimate is about 50.9 hydraulic hp. That is a serious hydraulic power figure for demanding hydraulic functions. It is a comparison number, not engine horsepower.
What do the New Holland TM190 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II/IIIN, hitch control is electronic lower-link draft control, and listed lift is 17500 lbs | 7938 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
