The New Holland T6.150 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 18.5 gpm (open) | 70.0 lpm, hydraulic type is open center | open center closed center load sensing (Optional), and valves/remotes are listed as 2 to 4.
Hydraulic Flow18.5 gpm (open) | 70.0 lpm
Hydraulic Typeopen center | open center closed center load sensing (Optional)
Valves / Remotes2 to 4
Lift Capacity6720 lbs | 3048 kg
New Holland T6.150 Hydraulic Capacity & Flow Specs
Hydraulic type
open center | open center closed center load sensing (Optional)
Pump flow
18.5 gpm (open) | 70.0 lpm
Total hydraulic flow
29 gpm (open) | 109.8 lpm
Steering flow
12.4 gpm | 46.9 lpm
Rear remotes
2 to 4
New Holland T6.150 Hitch, Remote & Lift Specs
Rear hitch type
II
Rear hitch control
electronic draft control
Rear lift at 24 inches
6720 lbs | 3048 kg
New Holland T6.150 Useful Hydraulic Calculations
Total flow vs pump flow
156.8% of listed pump flow
Steering flow vs pump flow
67% of listed pump flow
Rear lift per pump gpm
363.2 lb per gpm
New Holland T6.150 Hydraulic Comparison Charts
Pump flow comparison
This model
18.5 gpm
Average
14 gpm
Low
6 gpm
High
28 gpm
Rear lift comparison
This model
6,720 lb
Average
7,000 lb
Low
3,000 lb
High
12,000 lb
Benchmarks use practical low, average and high ranges for the utility and row-crop tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
New Holland T6.150 Steering, Brakes & Mechanical Hydraulic Notes
Steering
hydrostatic power
Brakes
Hydraulic wet disc brakes
New Holland T6.150 Hydraulic Capacity FAQ
Why is the New Holland T6.150 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the New Holland T6.150, but pump flow is 18.5 gpm (open) | 70.0 lpm, system type is open center | open center closed center load sensing (Optional), and lift is listed as 6720 lbs | 3048 kg. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the New Holland T6.150 hydraulics feel fast or slow?
The useful speed clue is 18.5 gpm (open) | 70.0 lpm pump flow, above the 14 gpm benchmark for this group. That is the spec that helps loader cycle speed, remote response and hydraulic implement speed.
What matters most for loader speed on the New Holland T6.150?
On the New Holland T6.150, 18.5 gpm (open) | 70.0 lpm pump flow points to quicker loader and cylinder movement and 6,720 lb listed lift is the number to watch for implement weight. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the New Holland T6.150?
For implement matching, the useful checks are 18.5 gpm flow, 6,720 lb listed lift, 2 to 4 remote/valve listing, and II hitch. That combination is fast enough on paper for quicker cylinder movement than many tractors in this size group, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Is the New Holland T6.150 rear lift capacity strong?
The listed lift figure is 6720 lbs | 3048 kg, close to the 7,000 lb benchmark. It is in the normal range, so implement length and ballast matter as much as the headline lift number.
Are the New Holland T6.150 hydraulic remotes enough?
The New Holland T6.150 remote/valve listing is 2 to 4. Because that wording may be optional or configuration-dependent, treat it as a setup check before buying an implement that needs rear hydraulic outlets.
Will the New Holland T6.150 hydraulics handle long hydraulic jobs?
The useful heat clues are 18.5 gpm flow. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
What do the New Holland T6.150 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is II, hitch control is electronic draft control, and listed lift is 6720 lbs | 3048 kg. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the New Holland T6.150 use?
The hydraulic system is listed as open center | open center closed center load sensing (Optional) with 18.5 gpm (open) | 70.0 lpm pump flow. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
What should you check before servicing the New Holland T6.150 hydraulics?
For service planning, the system is listed as open center | open center closed center load sensing (Optional) and flow is listed at 18.5 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Official information note
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official newholland.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
