The Massey Ferguson 7140 tractor cooling system capacity is 3.3 gal | 12.5 L, coolant type is ethylene glycol-based coolant, and coolant change interval is every 500 hours.
Massey Ferguson 7140 Coolant Capacity Details
Cooling system capacity
3.3 gal | 12.5 L
Coolant type
Ethylene glycol-based coolant
Coolant change interval
Every 500 hours
Coolant mixture ratio
50/50 antifreeze and water
Radiator cap pressure
13 psi | 90 kPa
Coolant Capacity Comparison Chart
Coolant Capacity Comparison
This model
3.3 gal
Average
5.5 gal
Low
3 gal
High
9 gal
Benchmarks use practical low, average and high coolant-capacity ranges for the utility tractor category. Use the exact tractor manual before buying coolant.
Massey Ferguson 7140 Extra Coolant Notes
Engine horsepower
140 hp | 104 kW
Capacity note
For the Massey Ferguson 7140, the listed cooling system capacity is 3.3 gal | 12.5 L. Buy slightly more coolant than the exact capacity so you have enough for topping off after air burps out.
Mixture note
50/50 antifreeze and water.
Radiator cap note
The radiator cap pressure listed for the Massey Ferguson 7140 is 13 psi | 90 kPa. Do not replace it with a random cap unless the pressure rating matches.
Refill note
Refill slowly, run the tractor until warm with the heater circuit open if fitted, let it cool, then recheck the coolant level. Never remove a hot radiator cap under pressure.
Massey Ferguson 7140 Coolant FAQs
How much coolant does a Massey Ferguson 7140 take?
The Massey Ferguson 7140 takes 3.3 gal | 12.5 L of coolant. That is on the low side for the utility tractor benchmark, which makes the refill cheaper, but the level still needs to be checked after the first heat cycle.
Is 3.3 gal | 12.5 L a small coolant capacity for a Massey Ferguson 7140?
It is low compared with the benchmark on this page. That makes the job cheaper, but it does not make coolant choice or bleeding less important.
How many coolant jugs do I need for a Massey Ferguson 7140?
This is a manageable refill amount. A 3.3 gal | 12.5 L system needs about 4 one-gallon containers if you are using premixed coolant. If using concentrate at a 50/50 mix, plan on about 1.6 gal of concentrate and 1.6 gal of distilled water. In metric terms, that is roughly 3 x 5 L containers for a full premix refill.
What coolant should I use in a Massey Ferguson 7140?
The listed coolant is ethylene glycol-based coolant. Ethylene glycol tells you the base coolant, but the additive package still matters on diesel engines, so match the manual or an approved equivalent. The listed mix is 50/50 antifreeze and water, so do not run straight water except as a short emergency move.
How much concentrate and water does a Massey Ferguson 7140 need?
With the listed 50/50 antifreeze and water mix, a full 3.3 gal | 12.5 L refill works out to about 1.6 gal of antifreeze concentrate and 1.6 gal of distilled water. If using premix, do not add extra water unless the product label says to.
Can I use a different radiator cap on a Massey Ferguson 7140?
The listed cap pressure is 13 psi | 90 kPa. That higher-pressure cap helps raise the boiling point, but only if the radiator neck, hoses and overflow path are in good shape. A weak cap or damaged seat can still cause coolant loss.
Official information note
Mistakes do happen. Coolant specs can change by year, engine, market, radiator option and coolant chemistry. Check the operator manual, parts book and official masseyferguson.com website before draining, flushing or refilling the cooling system.
