The Massey Ferguson 4708M tractor cooling system capacity is 3.2 gal | 12 L, coolant type is 50/50 ethylene glycol-based coolant, and coolant change interval is the coolant capacity of the Massey Ferguson 4708 tractor is approximately 12.5 liters (3.3 gallons).
Massey Ferguson 4708M Coolant Capacity Details
Cooling system capacity
3.2 gal | 12 L
Coolant type
50/50 ethylene glycol-based coolant
Coolant change interval
The coolant capacity of the Massey Ferguson 4708 tractor is approximately 12.5 liters (3.3 gallons)
Coolant mixture ratio
50/50 antifreeze and water
Radiator cap pressure
10 psi | 70 kPa
Coolant Capacity Comparison Chart
Coolant Capacity Comparison
This model
3.2 gal
Average
5.5 gal
Low
3 gal
High
9 gal
Benchmarks use practical low, average and high coolant-capacity ranges for the utility tractor category. Use the exact tractor manual before buying coolant.
Massey Ferguson 4708M Extra Coolant Notes
Engine horsepower
75 hp | 56 kW
Engine displacement
4.4 L | 268.5 cu in
Capacity note
For the Massey Ferguson 4708M, the listed cooling system capacity is 3.2 gal | 12 L. Buy slightly more coolant than the exact capacity so you have enough for topping off after air burps out.
Mixture note
50/50 antifreeze and water.
Radiator cap note
The radiator cap pressure listed for the Massey Ferguson 4708M is 10 psi | 70 kPa. Do not replace it with a random cap unless the pressure rating matches.
Refill note
Refill slowly, run the tractor until warm with the heater circuit open if fitted, let it cool, then recheck the coolant level. Never remove a hot radiator cap under pressure.
Massey Ferguson 4708M Coolant FAQs
How much coolant does a Massey Ferguson 4708M take?
The Massey Ferguson 4708M takes 3.2 gal | 12 L of coolant. That is on the low side for the utility tractor benchmark, which makes the refill cheaper, but the level still needs to be checked after the first heat cycle.
Is 3.2 gal | 12 L a small coolant capacity for a Massey Ferguson 4708M?
It is low compared with the benchmark on this page. That makes the job cheaper, but it does not make coolant choice or bleeding less important.
How many coolant jugs do I need for a Massey Ferguson 4708M?
This is a manageable refill amount. A 3.2 gal | 12 L system needs about 4 one-gallon containers if you are using premixed coolant. If using concentrate at a 50/50 mix, plan on about 1.6 gal of concentrate and 1.6 gal of distilled water. In metric terms, that is roughly 3 x 5 L containers for a full premix refill.
What coolant should I use in a Massey Ferguson 4708M?
The listed coolant is 50/50 ethylene glycol-based coolant. Ethylene glycol tells you the base coolant, but the additive package still matters on diesel engines, so match the manual or an approved equivalent. The listed mix is 50/50 antifreeze and water, so do not run straight water except as a short emergency move.
How much concentrate and water does a Massey Ferguson 4708M need?
With the listed 50/50 antifreeze and water mix, a full 3.2 gal | 12 L refill works out to about 1.6 gal of antifreeze concentrate and 1.6 gal of distilled water. If using premix, do not add extra water unless the product label says to.
Can I use a different radiator cap on a Massey Ferguson 4708M?
The listed cap pressure is 10 psi | 70 kPa. Use the same pressure rating when replacing it. The cap is part of the cooling system, not just a lid, and the wrong rating can cause boil-over, leaks or pressure problems.
Official information note
Mistakes do happen. Coolant specs can change by year, engine, market, radiator option and coolant chemistry. Check the operator manual, parts book and official masseyferguson.com website before draining, flushing or refilling the cooling system.
