The Gehl VT320 skid-steer battery size is Group 58, and it uses a 12-volt electrical system. Its 950 CCA rating is high for Gehl skid-steers in this dataset.
ModelVT320
BrandGehl
Voltage12 V
EquipmentSkid Steer
Voltage
12 V
Cold cranking
950 CCA
Battery size
Group 58
Battery location
See details below
How this battery compares
Compared with other Gehl skid-steer battery ratings in this dataset.
Cold cranking amps950 CCA
High
LowAverageHigh
Low 105 CCAMedian 800 CCAHigh 950 CCA
BA
Battery specification
Model-specific replacement data
System voltage
12 V
Battery group size
Group 58
Cold cranking amps
950 CCA
RP
Replacement battery
What to match when buying
Use a heavy-duty 12 V starting battery in BCI Group 31 with about 950 CCA (or higher), provided the case dimensions, hold-down and terminal orientation match. AGM is a good upgrade for vibration resistance; verify the machine serial number before purchase.
LC
Battery location
Where the battery is mounted
Family-match guidance: The battery on the Gehl VT230 skid steer loader is typically located under the operator's seat, providing easy access for maintenance and replacement. For specific battery specifications and replacement procedures, it's best to consult the owner's manual or contact a Gehl dealer. Verify the exact access panel/compartment for the machine serial number before service.
ID
Model details
Equipment identity
Brand
Gehl
Model
VT320
Equipment class
Skid-Steer Loader
HOW
How to replace the battery
Basic replacement procedure
Park on level ground, lower the lift arms/attachment, stop the engine, remove the key and isolate electrical power. Open the battery access, disconnect the negative cable first and then positive, remove the hold-down and lift out the battery. Clean the tray/terminals, install the replacement securely, connect positive first and negative last, then verify charging voltage and starting operation.
!
Bad battery symptoms
Signs the battery may be failing
Common signs are slow or no cranking, repeated clicking from the starter/solenoid, dim or flickering lights/display, electronics resetting during crank, needing frequent jump-starts, rapid self-discharge, corroded/swollen battery case, or resting voltage that quickly falls under load. Confirm cable condition and alternator output before condemning the battery.
?
What battery size fits the Gehl VT320?
Quick answer
The Gehl VT320 skid steer loader uses a battery group size 58.
?
How many CCA does the Gehl VT320 need?
Quick answer
950 CCA. Best available fitment is based on closest same-brand/model-family match (V420); an equal-or-higher CCA replacement is acceptable if the physical size and terminals match.
?
What voltage battery does the Gehl VT320 use?
Quick answer
The Gehl VT320 skid steer loader uses a battery with a voltage of 12 volts. For specific replacement options, it's best to consult the manufacturer's guidelines or a dealer for compatible battery models.
?
Where is the battery on the Gehl VT320?
Quick answer
Family-match guidance: The battery on the Gehl VT230 skid steer loader is typically located under the operator's seat, providing easy access for maintenance and replacement. For specific battery specifications and replacement procedures, it's best to consult the owner's manual or contact a Gehl dealer. Verify the exact access panel/compartment for the machine serial number before service.
?
What is the best replacement battery for the Gehl VT320?
Quick answer
Use a heavy-duty 12 V starting battery in BCI Group 31 with about 950 CCA (or higher), provided the case dimensions, hold-down and terminal orientation match. AGM is a good upgrade for vibration resistance; verify the machine serial number before purchase.
Disclaimer: Battery specifications are for general reference and may vary by year, serial number or configuration. Always verify fitment and electrical requirements before purchase or installation. See the Gehl website for manufacturer information.
