The Case IH CS 120 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 21.1 gpm | 79.9 lpm, and hydraulic pressure is 2683 psi | 185.0 bar.
Case IH CS 120 Hydraulic Capacity & Flow Specs
| Hydraulic pressure | 2683 psi | 185.0 bar |
|---|---|
| Pump flow | 21.1 gpm | 79.9 lpm |
Case IH CS 120 Hitch, Remote & Lift Specs
| Rear hitch type | III |
|---|
Case IH CS 120 Useful Hydraulic Calculations
| Estimated hydraulic horsepower | about 33 hydraulic hp from listed pressure and pump flow |
|---|
Case IH CS 120 Hydraulic Comparison Charts
Pump flow comparison
Hydraulic pressure comparison
Benchmarks use practical low, average and high ranges for the large ag tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
Case IH CS 120 Steering, Brakes & Mechanical Hydraulic Notes
| Steering | Power steering |
|---|---|
| Brakes | Wet disc brakes |
Case IH CS 120 Hydraulic Capacity FAQ
Why is the Case IH CS 120 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the Case IH CS 120, but pump flow is 21.1 gpm | 79.9 lpm and pressure is 2683 psi | 185.0 bar. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the Case IH CS 120 hydraulics feel fast or slow?
The useful speed clue is 21.1 gpm | 79.9 lpm pump flow, below the 50 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the Case IH CS 120 hydraulic pressure tell you?
The pressure spec is 2683 psi | 185.0 bar, below the 3,100 psi benchmark. Pressure is the force side of hydraulics, so this matters more for lift and cylinder push than for speed.
What matters most for loader speed on the Case IH CS 120?
On the Case IH CS 120, 21.1 gpm | 79.9 lpm pump flow points to slower loader and cylinder movement and 2,683 psi pressure affects force more than speed. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the Case IH CS 120?
For implement matching, the useful checks are 21.1 gpm flow, 2,683 psi pressure, and III hitch. That combination is more likely to feel slow on loaders, rear remotes and large cylinders and not a brute-force hydraulic setup compared with higher-pressure systems, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Will the Case IH CS 120 hydraulics handle long hydraulic jobs?
The useful heat clues are 21.1 gpm flow, 2,683 psi pressure, and about 33 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the Case IH CS 120 make on paper?
Using 2,683 psi and 21.1 gpm, the rough pressure-flow estimate is about 33 hydraulic hp. That is a useful middle-range hydraulic power figure for normal tractor work. It is a comparison number, not engine horsepower.
What do the Case IH CS 120 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is III. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What should you check before servicing the Case IH CS 120 hydraulics?
For service planning, pressure is listed at 2,683 psi and flow is listed at 21.1 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official caseih.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
