The Caterpillar 297D2 HXP skid-steer battery size should be verified for the specific machine, and it uses a 12-volt electrical system. Its 800 CCA rating is average for Caterpillar skid-steers in this dataset.
Model297D2 HXP
BrandCaterpillar
Voltage12 V
EquipmentSkid Steer
Voltage
12 V
Cold cranking
800 CCA
Battery size
Check physical fitment
Battery location
See details below
How this battery compares
Compared with other Caterpillar skid-steer battery ratings in this dataset.
Cold cranking amps800 CCA
Average
LowAverageHigh
Low 125 CCAMedian 850 CCAHigh 1400 CCA
BA
Battery specification
Model-specific replacement data
System voltage
12 V
Battery group size
Check physical fitment
Cold cranking amps
800 CCA
RP
Replacement battery
What to match when buying
The Cat part number 115-2422 is a 12V heavy-duty maintenance-free battery with 1000 cold crank amps and 31 BCI, designed for Cat compact track loaders including the 297D2 XHP.
LC
Battery location
Where the battery is mounted
Family-match guidance: The battery on the Caterpillar 297D2 skid steer loader is typically located under the rear left corner of the machine, behind an access panel. Verify the exact access panel/compartment for the machine serial number before service.
ID
Model details
Equipment identity
Brand
Caterpillar
Model
297D2 HXP
Equipment class
Skid-Steer Loader
HOW
How to replace the battery
Basic replacement procedure
Park on level ground, lower the lift arms/attachment, stop the engine, remove the key and isolate electrical power. Open the battery access, disconnect the negative cable first and then positive, remove the hold-down and lift out the battery. Clean the tray/terminals, install the replacement securely, connect positive first and negative last, then verify charging voltage and starting operation.
!
Bad battery symptoms
Signs the battery may be failing
Common signs are slow or no cranking, repeated clicking from the starter/solenoid, dim or flickering lights/display, electronics resetting during crank, needing frequent jump-starts, rapid self-discharge, corroded/swollen battery case, or resting voltage that quickly falls under load. Confirm cable condition and alternator output before condemning the battery.
?
What battery size fits the Caterpillar 297D2 HXP?
Quick answer
The official Caterpillar 297D2 XHP skid steer loader battery group size is 65 BCI. For replacement, you can consider the Cat part 230-6368, which is a 12-Volt heavy-duty battery with 850 cold cranking amps (CCA) designed for tough environments.
?
How many CCA does the Caterpillar 297D2 HXP need?
Quick answer
The Caterpillar 297D2 XHP skid steer loader typically requires a battery with a minimum of 800 CCA (Cold Cranking Amps) for optimal performance. Always refer to the official Caterpillar specifications or consult your dealer for the exact battery model and specifications.
?
What voltage battery does the Caterpillar 297D2 HXP use?
Quick answer
The Caterpillar 297D2 XHP skid steer loader uses a 12-volt battery. For battery replacement, it's important to follow the manufacturer's guidelines to ensure compatibility and performance.
?
Where is the battery on the Caterpillar 297D2 HXP?
Quick answer
Family-match guidance: The battery on the Caterpillar 297D2 skid steer loader is typically located under the rear left corner of the machine, behind an access panel. Verify the exact access panel/compartment for the machine serial number before service.
?
What is the best replacement battery for the Caterpillar 297D2 HXP?
Quick answer
The Cat part number 115-2422 is a 12V heavy-duty maintenance-free battery with 1000 cold crank amps and 31 BCI, designed for Cat compact track loaders including the 297D2 XHP.
Disclaimer: Battery specifications are for general reference and may vary by year, serial number or configuration. Always verify fitment and electrical requirements before purchase or installation. See the Caterpillar website for manufacturer information.
