The Caterpillar 268B skid-steer battery size is Group 24, and it uses a 12-volt electrical system. Its 1400 CCA rating is high for Caterpillar skid-steers in this dataset.
Model268B
BrandCaterpillar
Voltage12 V
EquipmentSkid Steer
Voltage
12 V
Cold cranking
1400 CCA
Battery size
Group 24
Battery location
See details below
How this battery compares
Compared with other Caterpillar skid-steer battery ratings in this dataset.
Cold cranking amps1400 CCA
High
LowAverageHigh
Low 125 CCAMedian 850 CCAHigh 1400 CCA
BA
Battery specification
Model-specific replacement data
System voltage
12 V
Battery group size
Group 24
Cold cranking amps
1400 CCA
RP
Replacement battery
What to match when buying
Use a heavy-duty 12 V starting battery in BCI Group 24 with about 1400 CCA (or higher), provided the case dimensions, hold-down and terminal orientation match. AGM is a good upgrade for vibration resistance; verify the machine serial number before purchase.
LC
Battery location
Where the battery is mounted
Family-match guidance: The battery on the Caterpillar 262B skid steer loader is typically located under the seat or in the rear compartment of the machine. For specific replacement instructions and specifications, it's best to refer to the official Caterpillar resources or service manuals. Verify the exact access panel/compartment for the machine serial number before service.
ID
Model details
Equipment identity
Brand
Caterpillar
Model
268B
Equipment class
Skid-Steer Loader
HOW
How to replace the battery
Basic replacement procedure
Park on level ground, lower the lift arms/attachment, stop the engine, remove the key and isolate electrical power. Open the battery access, disconnect the negative cable first and then positive, remove the hold-down and lift out the battery. Clean the tray/terminals, install the replacement securely, connect positive first and negative last, then verify charging voltage and starting operation.
!
Bad battery symptoms
Signs the battery may be failing
Common signs are slow or no cranking, repeated clicking from the starter/solenoid, dim or flickering lights/display, electronics resetting during crank, needing frequent jump-starts, rapid self-discharge, corroded/swollen battery case, or resting voltage that quickly falls under load. Confirm cable condition and alternator output before condemning the battery.
?
What battery size fits the Caterpillar 268B?
Quick answer
Group 24. Best available fitment is based on closest same-brand/model-family match (216B); confirm tray dimensions, terminal layout, and serial number before ordering.
?
How many CCA does the Caterpillar 268B need?
Quick answer
1400 CCA. Best available fitment is based on closest same-brand/model-family match (216B); an equal-or-higher CCA replacement is acceptable if the physical size and terminals match.
?
What voltage battery does the Caterpillar 268B use?
Quick answer
12 volts. Skid-steer starting/charging systems for this model family use a 12 V battery system; confirm serial-specific configuration before replacement.
?
Where is the battery on the Caterpillar 268B?
Quick answer
Family-match guidance: The battery on the Caterpillar 262B skid steer loader is typically located under the seat or in the rear compartment of the machine. For specific replacement instructions and specifications, it's best to refer to the official Caterpillar resources or service manuals. Verify the exact access panel/compartment for the machine serial number before service.
?
What is the best replacement battery for the Caterpillar 268B?
Quick answer
Use a heavy-duty 12 V starting battery in BCI Group 24 with about 1400 CCA (or higher), provided the case dimensions, hold-down and terminal orientation match. AGM is a good upgrade for vibration resistance; verify the machine serial number before purchase.
Disclaimer: Battery specifications are for general reference and may vary by year, serial number or configuration. Always verify fitment and electrical requirements before purchase or installation. See the Caterpillar website for manufacturer information.
