The Massey Ferguson 4283 tractor cooling system capacity is 25.1 gal | 95 L and coolant type is 50/50 ethylene glycol-based coolant.
Massey Ferguson 4283 Coolant Capacity Details
Cooling system capacity
25.1 gal | 95 L
Coolant type
50/50 ethylene glycol-based coolant
Coolant mixture ratio
50/50 antifreeze and water
Coolant Capacity Comparison Chart
Coolant Capacity Comparison
This model
25.1 gal
Average
5.5 gal
Low
3 gal
High
9 gal
Benchmarks use practical low, average and high coolant-capacity ranges for the utility tractor category. Use the exact tractor manual before buying coolant.
Massey Ferguson 4283 Extra Coolant Notes
Engine horsepower
85 hp | 63.4 kW
Engine displacement
4.1 L | 250 cu in
Capacity note
For the Massey Ferguson 4283, the listed cooling system capacity is 25.1 gal | 95 L. Buy slightly more coolant than the exact capacity so you have enough for topping off after air burps out.
Mixture note
50/50 antifreeze and water.
Refill note
Refill slowly, run the tractor until warm with the heater circuit open if fitted, let it cool, then recheck the coolant level. Never remove a hot radiator cap under pressure.
Massey Ferguson 4283 Coolant FAQs
How much coolant does a Massey Ferguson 4283 take?
The Massey Ferguson 4283 takes 25.1 gal | 95 L of coolant. That is well above the normal utility tractor benchmark shown here, so treat it as a full cooling-system service job, not a quick top-up.
Is 25.1 gal | 95 L a lot of coolant for a Massey Ferguson 4283?
Yes. For this tractor category, 25.1 gal | 95 L is well above normal. This is the sort of refill where you want all coolant on hand before draining, because stopping halfway through the job is annoying and messy.
How many coolant jugs do I need for a Massey Ferguson 4283?
Do not underestimate this refill. A 25.1 gal | 95 L system needs about 26 one-gallon containers if you are using premixed coolant. If using concentrate at a 50/50 mix, plan on about 12.6 gal of concentrate and 12.6 gal of distilled water. In metric terms, that is roughly 19 x 5 L containers for a full premix refill.
What coolant should I use in a Massey Ferguson 4283?
The listed coolant is 50/50 ethylene glycol-based coolant. Ethylene glycol tells you the base coolant, but the additive package still matters on diesel engines, so match the manual or an approved equivalent. The listed mix is 50/50 antifreeze and water, so do not run straight water except as a short emergency move.
How much concentrate and water does a Massey Ferguson 4283 need?
With the listed 50/50 antifreeze and water mix, a full 25.1 gal | 95 L refill works out to about 12.6 gal of antifreeze concentrate and 12.6 gal of distilled water. If using premix, do not add extra water unless the product label says to.
Is the Massey Ferguson 4283 coolant capacity large for its engine?
The Massey Ferguson 4283 has 85 hp | 63.4 kW and 4.1 L | 250 cu in listed alongside a 25.1 gal | 95 L cooling system. That is a lot of coolant for the horsepower figure, which usually points to the whole radiator, block, hose and cooling-package volume rather than engine size alone. Coolant capacity is not decided by displacement alone; the radiator, hoses, block passages and options all count.
Official information note
Mistakes do happen. Coolant specs can change by year, engine, market, radiator option and coolant chemistry. Check the operator manual, parts book and official masseyferguson.com website before draining, flushing or refilling the cooling system.
