The Massey Ferguson 220 tractor hydraulic oil capacity was not listed in the scraped specs, but hydraulic pump flow is 5.4 gpm | 20.4 lpm, hydraulic pressure is 1700 psi | 117.2 bar, and hydraulic type is open center.
Massey Ferguson 220 Hydraulic Capacity & Flow Specs
| Hydraulic type | open center |
|---|---|
| Hydraulic pressure | 1700 psi | 117.2 bar |
| Pump flow | 5.4 gpm | 20.4 lpm |
Massey Ferguson 220 Hitch, Remote & Lift Specs
| Rear hitch type | I |
|---|---|
| Rear hitch control | position control |
Massey Ferguson 220 Useful Hydraulic Calculations
| Estimated hydraulic horsepower | about 5.4 hydraulic hp from listed pressure and pump flow |
|---|
Massey Ferguson 220 Hydraulic Comparison Charts
Pump flow comparison
Hydraulic pressure comparison
Benchmarks use practical low, average and high ranges for the compact and small utility tractor category. These are comparison guides only; use the operator manual and exact tractor configuration before buying parts, oil, loaders or hydraulic implements.
Massey Ferguson 220 Steering, Brakes & Mechanical Hydraulic Notes
| Steering | Manual steering |
|---|---|
| Differential lock | mechanical rear |
Massey Ferguson 220 Hydraulic Capacity FAQ
Why is the Massey Ferguson 220 hydraulic oil capacity not shown here?
The scraped specs do not list a hydraulic oil capacity for the Massey Ferguson 220, but pump flow is 5.4 gpm | 20.4 lpm, pressure is 1700 psi | 117.2 bar, and system type is open center. For oil fill amount, use the manual or fill/check procedure, not pump flow or pressure.
Will the Massey Ferguson 220 hydraulics feel fast or slow?
The useful speed clue is 5.4 gpm | 20.4 lpm pump flow, below the 8 gpm benchmark for this group. Expect hydraulic functions to be steady rather than fast, especially with loaders or big cylinders.
What does the Massey Ferguson 220 hydraulic pressure tell you?
The pressure spec is 1700 psi | 117.2 bar, below the 2,300 psi benchmark. Pressure is the force side of hydraulics, so this matters more for lift and cylinder push than for speed.
What matters most for loader speed on the Massey Ferguson 220?
On the Massey Ferguson 220, 5.4 gpm | 20.4 lpm pump flow points to slower loader and cylinder movement and 1,700 psi pressure affects force more than speed. Flow is the speed number; pressure and lift are the force numbers.
How do you judge hydraulic implement fit on the Massey Ferguson 220?
For implement matching, the useful checks are 5.4 gpm flow, 1,700 psi pressure, and I hitch. That combination is more likely to feel slow on loaders, rear remotes and large cylinders and not a brute-force hydraulic setup compared with higher-pressure systems, so match the implement by hydraulic demand, hitch category and actual tractor setup rather than model name alone.
Will the Massey Ferguson 220 hydraulics handle long hydraulic jobs?
The useful heat clues are 5.4 gpm flow, 1,700 psi pressure, and about 5.4 hydraulic hp by the pressure-flow estimate. Heat risk still depends on load, duty cycle, oil level, cooler condition and implement demand.
How much hydraulic power does the Massey Ferguson 220 make on paper?
Using 1,700 psi and 5.4 gpm, the rough pressure-flow estimate is about 5.4 hydraulic hp. That is a modest hydraulic power figure, so huge hydraulic loads are not the point of this setup. It is a comparison number, not engine horsepower.
What do the Massey Ferguson 220 hitch hydraulic specs mean?
The hitch-side hydraulic clues are that rear hitch type is I and hitch control is position control. For real implement choice, hitch category gets it connected, lift capacity gets it raised, and hydraulic flow gets cylinders moving at a usable speed.
What hydraulic system does the Massey Ferguson 220 use?
The hydraulic system is listed as open center with 5.4 gpm | 20.4 lpm pump flow and 1700 psi | 117.2 bar pressure. The system type tells you how the hydraulics are arranged; the flow and pressure numbers tell you more about real-world speed and force.
What should you check before servicing the Massey Ferguson 220 hydraulics?
For service planning, the system is listed as open center, pressure is listed at 1,700 psi, and flow is listed at 5.4 gpm. Use the dipstick or sight glass and the operator manual as the final source before servicing.
Hydraulic capacity, pressure, flow, valves, remotes and lift specs can vary by year, market, transmission, pump option, loader package and tractor configuration. Check the operator manual, hydraulic oil dipstick/sight glass, parts book and official masseyferguson.com website before buying hydraulic oil, servicing the system or sizing hydraulic implements.
